Printable Version | Subscribe | Add to Favourites
New Topic New Reply
Author: Subject: Brake pedal panel reinforcement
Slimy38

posted on 22/8/18 at 07:16 AM Reply With Quote
Brake pedal panel reinforcement

One of the things I read on the interweb talked about the drivers side footwell panel flexing under braking, and I have an opportunity at the moment to reinforce it. However, I'd like to know if it's actually a thing to worry about or whether it is an uncommon occurrence.

I've used the recommended Haynes Roadster 3mm metal plate, split in two with the bottom half carrying the brake and clutch master cylinders (MX5 donor hence the hydraulic clutch). The lower half is bolted to the other half and to the chassis member at the bottom and seems fairly solid, but I know the average braking force exerted by a human can be quite significant. Obviously even though the clutch is also hydraulic it won't be adding to my troubles.

If anyone has reinforced this panel, do you have any photos showing what you've done and what benefits it's given? Or is it less of an issue than people say?

View User's Profile View All Posts By User U2U Member
mark chandler

posted on 22/8/18 at 07:36 AM Reply With Quote
3mm is pretty hefty steel, much thicker than car manufacturers so I doubt you have a problem.

My bulkhead is 1/16" steel, I cut a spreader plate to reinforce where required, I doubt you have anything to worry about.

[Edited on 22/8/18 by mark chandler]

View User's Profile View All Posts By User U2U Member
40inches

posted on 22/8/18 at 08:17 AM Reply With Quote
Yep, 3mm is more than man enough. Mine is still solid after 4000 miles
Description
Description

View User's Profile View All Posts By User U2U Member
Slimy38

posted on 22/8/18 at 08:33 AM Reply With Quote
Perfect, thanks for the confirmation. One less thing to worry about.
View User's Profile View All Posts By User U2U Member
pewe

posted on 22/8/18 at 11:23 AM Reply With Quote
If you do encounter flex (unlikely given your steel thickness) fabricate a brake master cylinder stopper.
I've knocked them up for the hairdressers and son's IntegraType R to good effect.
A google search will bring up several accessory ones but at £100+ it's taking the wee.
HTH.
Cheeers, Pewe10

View User's Profile View All Posts By User U2U Member
Mr Whippy

posted on 22/8/18 at 12:38 PM Reply With Quote
It may flex although I doubt it, but even then it's not going to rip out is it? Sounds like beefing it up would be just useless extra weight. What's the thickness on a production car 0.8 - 2mm even in high load areas such as subframes and suspension mounts. If you still want to stiffen it up do it properly with webs not plates
View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
Slimy38

posted on 22/8/18 at 01:05 PM Reply With Quote
quote:
Originally posted by pewe
If you do encounter flex (unlikely given your steel thickness) fabricate a brake master cylinder stopper.
I've knocked them up for the hairdressers and son's IntegraType R to good effect.
A google search will bring up several accessory ones but at £100+ it's taking the wee.
HTH.
Cheeers, Pewe10


Oh yes of course, I'd forgotten about those. I remember seeing them when I was looking at MX5's for a donor. I think I'll keep that as my backup solution, thanks.

View User's Profile View All Posts By User U2U Member
Angel Acevedo

posted on 22/8/18 at 02:20 PM Reply With Quote
quote:
Originally posted by Slimy38
One of the things I read on the interweb talked about the drivers side footwell panel flexing under braking, and I have an opportunity at the moment to reinforce it. However, I'd like to know if it's actually a thing to worry about or whether it is an uncommon occurrence.

I've used the recommended Haynes Roadster 3mm metal plate, split in two with the bottom half carrying the brake and clutch master cylinders (MX5 donor hence the hydraulic clutch). The lower half is bolted to the other half and to the chassis member at the bottom and seems fairly solid, but I know the average braking force exerted by a human can be quite significant. Obviously even though the clutch is also hydraulic it won't be adding to my troubles.

If anyone has reinforced this panel, do you have any photos showing what you've done and what benefits it's given? Or is it less of an issue than people say?


I mounted my OBP Pedal box on top of two 25 X 25 mm X 3 mm Angle Iron welded to members D1 and the one across forming the bottom cornerof the footwell.
For you in GB would be D2
Regards
AA





Beware of what you wish.. for it may come true....

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member

New Topic New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.