Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: Brakes pull to left - only after not braking for some time
Crazysurf

posted on 19/2/20 at 07:02 PM Reply With Quote
Brakes pull to left - only after not braking for some time

I have an MG Midget (2ltr Zetec - not related) and have a strange problem that if I have been travelling for some time (e.g. on the motorway) and brake, it pulls to the left but then, if I brake again, all is good. Any ideas?
View User's Profile View All Posts By User U2U Member
JAG

posted on 19/2/20 at 08:10 PM Reply With Quote
Yeah - one caliper (right hand side, probably the front) is seizing slighty - it's happening while you're driving but not using the brakes.

After the first apply, when the brakes pull, the seizing eases off and it works fine again for a while. Until you don't brake for a while - then the problem repeats.

Best way to relieve the issue is replace the offending caliper.





Justin


Who is this super hero? Sarge? ...No.
Rosemary, the telephone operator? ...No.
Penry, the mild-mannered janitor? ...Could be!

View User's Profile View All Posts By User U2U Member
cliftyhanger

posted on 19/2/20 at 08:42 PM Reply With Quote
Indeed. But I would be buying a seal kit and doing both calipers. Not difficult as long as the pistons are not seized solid! (which yours are not by the sounds of it)
View User's Profile View All Posts By User U2U Member
number-1

posted on 19/2/20 at 08:44 PM Reply With Quote
Replace the caliper seals on both sides. Also remove and grease the pistons. Its a simple job and cheap to do.
View User's Profile View All Posts By User U2U Member
cliftyhanger

posted on 19/2/20 at 10:08 PM Reply With Quote
And use red brake/rubber grease. Copper grease is NOT suitable for seals/pistons/bleed nipples etc
View User's Profile View All Posts By User U2U Member
JAG

posted on 19/2/20 at 10:27 PM Reply With Quote
I'd replace rather than re-build but that's your call. However...

NEVER use a normal Mineral Oil based lubricant (grease, oil, WD40 etc...) on brake caliper seals.

The rubber they are made from will not tolerate it and the seal will gradually deteriorate until your brakes fail!

IF you want to lubricate them as you rebuild the caliper use the DOT brake fluid.





Justin


Who is this super hero? Sarge? ...No.
Rosemary, the telephone operator? ...No.
Penry, the mild-mannered janitor? ...Could be!

View User's Profile View All Posts By User U2U Member
steve m

posted on 20/2/20 at 12:14 AM Reply With Quote
I would, and have done, replace the seals, and pistons in the front calipers,

As long as everything is spotlessly clean, and rust free, the brakes will work 100%

I did it myself on my 7, as had similar issues, and the brakes, and driving were perfect afterwards

steve





Thats was probably spelt wrong, or had some grammer, that the "grammer police have to have a moan at




View User's Profile View All Posts By User U2U Member
Crazysurf

posted on 20/2/20 at 07:19 AM Reply With Quote
Thank you guys :-)
View User's Profile View All Posts By User U2U Member
Bluemoon

posted on 20/2/20 at 10:45 AM Reply With Quote
I used bigg red who supplied me with stainless steel pistons and seals. In theory the pistons should not rust and pit like the originals, great for a car that is standing over winter...

[Edited on 20/2/20 by Bluemoon]

View User's Profile View All Posts By User U2U Member
AlexXtreme

posted on 20/2/20 at 01:05 PM Reply With Quote
I had similar problem and did as the other said and refurbed the calipers my self.
Brought a kit for the seals and by accident saw a company selling st.steel pistons on ebay which were fantastic quality.
Use a car air compressor to remove the old pistons.

View User's Profile View All Posts By User U2U Member
gremlin1234

posted on 20/2/20 at 06:51 PM Reply With Quote
brake disk runout / slight warping, or failing wheel bearings can also cause symptoms like this.
(they knock the pads back a tiny bit further than the other side)

View User's Profile View All Posts By User U2U Member
StrikerChris

posted on 20/2/20 at 10:19 PM Reply With Quote
If its a single piston caliper on sliders I had similar years ago. Turned out the slides were worn (not seized),causing the caliper to cock and jam occasionally. Wasn't obvious at first, as every time I had the wheel off it all seemed free.
View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.