Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: Putting Dynamics 1.2 wheels on, what offset?
scoop

posted on 13/5/16 at 01:57 PM Reply With Quote
Putting Dynamics 1.2 wheels on, what offset?

Hi,
Wanting to change from the old set of TSW's I have on for some black 1.2's but I have no idea what offset to ask for. I've been told that there should be an ET mark on the wheel somewhere but there isn't.
The current ones are on the Sierra hubs so 4 X 100 with 6J X 15 wheels with 195/50 tyres at the moment.
Any suggestions?
Thanks

View User's Profile E-Mail User View All Posts By User U2U Member
loggyboy

posted on 13/5/16 at 02:07 PM Reply With Quote
Sierra Hubs are 4x108.
On the current wheels, measure the distance from the hub mounting face to the centre of the rim, thats the offset.





Mistral Motorsport

View User's Profile View All Posts By User U2U Member
scoop

posted on 13/5/16 at 02:14 PM Reply With Quote
That easy.
Love this forum.
Thanks

View User's Profile E-Mail User View All Posts By User U2U Member
loggyboy

posted on 13/5/16 at 02:25 PM Reply With Quote



[Edited on 13-5-16 by loggyboy]





Mistral Motorsport

View User's Profile View All Posts By User U2U Member
mcerd1

posted on 13/5/16 at 02:46 PM Reply With Quote
Have you taken the old wheels off to look for the offset mark - sometimes its on the bit that covered by the hub when you bolt them on...

Otherwise its easy enough to measure, but Sierra's are normally ET35 to ET38 and most cars based on them stick to something similar (unless its got a very wide rear end like my dax on ET0)
Always best to measure twice and buy once though


As above sierra's are 4x108 P.C.D's with a 63.4mm centre bore
(the centre bore is important, but most aftermarket wheels come with plastic spacer rings to clip in the centre to suit)


[Edited on 13/5/2016 by mcerd1]





-

View User's Profile View All Posts By User U2U Member
scoop

posted on 13/5/16 at 03:10 PM Reply With Quote
Yes wheels are off. Lots of numbers but none with ET prefix and others are too long.
Thanks for all your help. Will have a measure later and see what I get.
Thanks

View User's Profile E-Mail User View All Posts By User U2U Member
loggyboy

posted on 13/5/16 at 03:14 PM Reply With Quote
Pop some pics up. Sometimes they are quite obscurely numbered.





Mistral Motorsport

View User's Profile View All Posts By User U2U Member
scoop

posted on 13/5/16 at 03:19 PM Reply With Quote
At work now so will have to be the morning
View User's Profile E-Mail User View All Posts By User U2U Member
SJ

posted on 13/5/16 at 03:45 PM Reply With Quote
Mine are et38. That's on Sierra running gear with 13" TD pro 1.2s.
View User's Profile View All Posts By User U2U Member
Ben_Copeland

posted on 13/5/16 at 05:10 PM Reply With Quote
Generally et38 but could be et16 which is Peugeot offset same pcd.

A lot of wheels don't get stamped which is annoying





Ben

Locost Map on Google Maps


Z20LET Astra Turbo, into a Haynes Roadster

Enter Your Details Here
http://www.facebook.com/EquinoxProducts for all your bodywork needs!

View User's Profile View All Posts By User U2U Member
loggyboy

posted on 13/5/16 at 06:04 PM Reply With Quote
Bear in mind that offset is affected by wheel width also, in respect that any change in width is split evenly if offset stays the same.
Ie go from a 6 inch wide rim with 38 offset to a 7 inch rim with 38 offset the wheel and tyre will be close to the inside of car by 12.5mm and will stick 12.5mm further out. So if the width is changing, a check of clearances on inner and outer edges is necessary.
Further to this any increase in offset will bring spokes closer to caliper so clearance there can often be an issue of u have big brakes and/or small wheels.


Its also noteworthy it doesn't always matter what the donors car offset was, as the kit could have been designed or built (arches and mounts specifically) around a different offset.





Mistral Motorsport

View User's Profile View All Posts By User U2U Member
scoop

posted on 14/5/16 at 11:34 AM Reply With Quote
Measuring from where I think I should according to the diagram im getting 38ish but looking on another wheel I've found 35P which I couldn't see before.
Reading round the rim I've got 6015RAZ 35P 4 108 72NP C MWL560kg 1H74S363 200604.
Some are obvious, some aren't. I'm guessing I have an offset of 35 then?

View User's Profile E-Mail User View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.