Kliktronic electric gear change
Bought this secondhand a few months ago but change of plan so now for sale.
Full working order, I've tested it and it works exactly as it should.
Rod out of piston has very slight twist in it, not sure why but rod been slightly filed down on one side. Can't imagine why don't think it
would make any difference, maybe just vibration noise or something. But works absolutely spot on.
New mounting bracket
Control box has cracking on base plate. Not big deal as its fully sealed inside. Could either leave as is, put line of silicone round or pull off base
and make a new one.
Switches are included but have had it. Not expensive to replace if wants though.
Fitting instructions
Paddles from jag xf. Just paddles though with wires that I've soldered in. Soldering bit rough may want to redo but plenty strong and again
tested and work fine. Don't have mounting plate for paddles as I was going to make one. Easy enoung I reckon out of piece of Ali.
All wiring included.
Cheap electric paddle shift kit for someone, just needs a bit of work/tarting up. Like I say fully tested and working with no problems.
£150 anyone?
Very interested if it hasn't sold can you put up a picture or two of the damaged bits, does the box of tricks do up clutchless upshift and downshift? Ie cut the coils and blip the throttle?
quote:
Originally posted by marco
Very interested if it hasn't sold can you put up a picture or two of the damaged bits, does the box of tricks do up clutchless upshift and downshift? Ie cut the coils and blip the throttle?
Ok thanks, not for me then.
Flick u2u sent re shifter
Slight amendment to listing and price, can't find fitting instructions or buttons. Also found shaft slight rubbing when turned..spoke to klik
about this though. Still works fine.
quote:
Originally posted by Flick
Kliktronic electric gear change
Bought this secondhand a few months ago but change of plan so now for sale.
Full working order, I've tested it and it works exactly as it should.
Rod out of piston has very slight twist in it, not sure why but rod been slightly filed down on one side. Slight rubbing when shaft is one way, but turn it round, no problem. Spoke to kliktroni bout this and they said its fine, not uncommon, can be straightened in vice if really wanted. But to be honest, its fine as is so I haven't bothered.
New mounting bracket, no mounting holes drilled yet.
Control box has cracking on base plate. Not big deal as its fully sealed inside. Could either leave as is, put line of silicone round or pull off base and make a new one.
Switches are not include, but can be bought if required.
wires are labelled
Paddles from jag xf. Just paddles though with wires that I've soldered in. Don't have mounting plate for paddles as I was going to make one. Easy enoung I reckon out of piece of Ali.
All wiring included.
Cheap electric paddle shift kit for someone, just needs a bit of work/tarting up. Like I say fully tested and working with no problems.
£140 inc p&p
[Edited on 4/10/14 by Flick]
[Edited on 4/10/14 by Flick]
capri_big_jim - 4/10/14 at 07:06 PMI sent you a PM about this and never got a reply. I presumed you had sold it.
Jim
Flick - 4/10/14 at 09:09 PMquote:
Originally posted by capri_big_jim
I sent you a PM about this and never got a reply. I presumed you had sold it.
Jim
My apologies, though I'd replied to everyone.
capri_big_jim - 5/10/14 at 08:22 AMPm sent.
Flick - 5/10/14 at 09:16 AMquote:
Originally posted by capri_big_jim
Pm sent.
U2u replied to
capri_big_jim - 5/10/14 at 10:12 AMPM sent. I will take it mate.
Jim