Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: Fitting a towbar in rusty holes
JoelP

posted on 4/1/17 at 10:03 AM Reply With Quote
Fitting a towbar in rusty holes

My Jeep has not had a towbar fitted for 12 years, and now the mounting threads in a chassis rail are rusted beyond use. I'm thinking of drilling it up and replacing it with an m12 thread. Anyone done this, or any dire warnings? I can't see an alternative tbh.





Beware! Bourettes is binfectious.

View User's Profile View All Posts By User U2U Member
designer

posted on 4/1/17 at 10:23 AM Reply With Quote
Just run a tap through it.
View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
nick205

posted on 4/1/17 at 11:41 AM Reply With Quote
quote:
Originally posted by designer
Just run a tap through it.


That would be my first action - lube it and run a tap through to clean the thread.

The difficulty I see with drilling /tapping it larger is ensuring the drill / tap run squarely through the material. Out of interest what is the existing thread...M10?






View User's Profile View All Posts By User U2U Member
JoelP

posted on 4/1/17 at 02:13 PM Reply With Quote
Yeah m10. I got a bolt into it fine, but it wobbles even when fully through. The threads have rusted away, not just rusted up. In the process now of tapping it to m12.





Beware! Bourettes is binfectious.

View User's Profile View All Posts By User U2U Member
nick205

posted on 4/1/17 at 02:54 PM Reply With Quote
Fair enough - I assumed the existing thread would be rust covered.






View User's Profile View All Posts By User U2U Member
David Jenkins

posted on 4/1/17 at 03:45 PM Reply With Quote
Can you get to both sides of the rail? If so, why not thread a longer bolt through and back it up with a nut?






View User's Profile Visit User's Homepage View All Posts By User U2U Member
907

posted on 4/1/17 at 04:45 PM Reply With Quote
quote:
Originally posted by JoelP
Yeah m10. I got a bolt into it fine, but it wobbles even when fully through. The threads have rusted away, not just rusted up. In the process now of tapping it to m12.




Tapping to M12 is the way Joel.

!0.2mm is the drill size and this will take the old thread out completely.
Just make sure there's enough metal remaining after the M12.






View User's Profile View All Posts By User U2U Member
llionellis

posted on 4/1/17 at 06:27 PM Reply With Quote
Depending on age it could be UNC 10mm bolt would be slack (very slack) in a 7/16 unc tapped hole.
View User's Profile View All Posts By User U2U Member
bi22le

posted on 4/1/17 at 06:58 PM Reply With Quote
quote:
Originally posted by llionellis
Depending on age it could be UNC 10mm bolt would be slack (very slack) in a 7/16 unc tapped hole.


Its a 12year old Jeep. This was my thinking when I first read this. It won't be M10!





Track days ARE the best thing since sliced bread, until I get a supercharger that is!

Please read my ring story:
http://www.locostbuilders.co.uk/forum/13/viewthread.php?tid=139152&page=1

Me doing a sub 56sec lap around Brands Indy. I need a geo set up! http://www.youtube.com/watch?v=EHksfvIGB3I

View User's Profile View All Posts By User U2U Member
coyoteboy

posted on 4/1/17 at 11:17 PM Reply With Quote
Interestingly a search through forums suggests the engine and transmission bolts may be metric but a lot of the body bolts are UNC.






View User's Profile E-Mail User View All Posts By User U2U Member
nick205

posted on 5/1/17 at 08:58 AM Reply With Quote
quote:
Originally posted by llionellis
Depending on age it could be UNC 10mm bolt would be slack (very slack) in a 7/16 unc tapped hole.


I hadn't considered this and it could be on the money. If the hole is now drilled then tapping to M12 may be the only resolution.

As mentioned a nut on the other side could increase security of the fixing. Would a plain (untapped) hole then be batter?






View User's Profile View All Posts By User U2U Member
02GF74

posted on 5/1/17 at 08:32 PM Reply With Quote
quote:
Originally posted by nick205
Would a plain (untapped) hole then be batter?



It'lll be fine in that plaice.






View User's Profile View All Posts By User U2U Member
steve m

posted on 5/1/17 at 09:03 PM Reply With Quote
Am I not the only one, who thinks, "the holes are so rusty that the bolts pull through" and .................
If so the metal around, the said rusty threaded holes will be so rusty, that its wafer thin, the first tug on the towbar will rip the whole rear end of the car ?

maybe, its just me then







Thats was probably spelt wrong, or had some grammer, that the "grammer police have to have a moan at




View User's Profile View All Posts By User U2U Member
gremlin1234

posted on 5/1/17 at 09:15 PM Reply With Quote
another way to do it might be thread inserts / helicoils , but I don't think they are appropriate here.
View User's Profile View All Posts By User U2U Member
Adamirish

posted on 5/1/17 at 10:02 PM Reply With Quote
quote:
Originally posted by 02GF74
quote:
Originally posted by nick205
Would a plain (untapped) hole then be batter?



It'lll be fine in that plaice.




It cod be trouble.





MK Indy 1700 Xflow

View User's Profile View All Posts By User U2U Member
bi22le

posted on 5/1/17 at 11:19 PM Reply With Quote
quote:
Originally posted by nick205
quote:
Originally posted by llionellis
Depending on age it could be UNC 10mm bolt would be slack (very slack) in a 7/16 unc tapped hole.


I hadn't considered this and it could be on the money. If the hole is now drilled then tapping to M12 may be the only resolution.

As mentioned a nut on the other side could increase security of the fixing. Would a plain (untapped) hole then be batter?


Nuts in the other side would be fine if you can get there. You could lift your car from them 4 x M12 with bolts!

As long as the rust bit is bolted to hold ups. As previously mentioned.





Track days ARE the best thing since sliced bread, until I get a supercharger that is!

Please read my ring story:
http://www.locostbuilders.co.uk/forum/13/viewthread.php?tid=139152&page=1

Me doing a sub 56sec lap around Brands Indy. I need a geo set up! http://www.youtube.com/watch?v=EHksfvIGB3I

View User's Profile View All Posts By User U2U Member
nick205

posted on 6/1/17 at 11:51 AM Reply With Quote
quote:
Originally posted by 02GF74
quote:
Originally posted by nick205
Would a plain (untapped) hole then be batter?



It'lll be fine in that plaice.



Oooops! A typo there






View User's Profile View All Posts By User U2U Member
JoelP

posted on 6/1/17 at 01:09 PM Reply With Quote
Sorry for the slow reply guys, didn't see all these posts. I think you're right that it wasn't m10. Drilling it with a 10.5mm drill didn't remove all traces of rust, which I think rules out m10. My googling showed that an m12x1.75 thread starts from 10.5mm hole. As an aside, 'what hole...' on google throws up some amazing predictions - sex education isn't what it used to be!

So it now has 5 m12 bolts done up tight (6th is obscured by the exhaust, I'll get my mate to do that at the next service), and it pulled a tonne trailer fine.

Cheers for all the help.





Beware! Bourettes is binfectious.

View User's Profile View All Posts By User U2U Member
JoelP

posted on 6/1/17 at 01:11 PM Reply With Quote
Oh yeah, no access to get a nut behind.





Beware! Bourettes is binfectious.

View User's Profile View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.