Board logo

Nose cone mounting
S1502 - 11/1/18 at 07:44 PM

Just wondered how people have secured their nose cones?

Looking to re do mine but seeing how others have done it.

I have a tiger s6 currently secured two bolts underneath.

[Edited on 11/1/18 by S1502]


CosKev3 - 11/1/18 at 08:06 PM

Mines currently got 2 bolts into both top chassis rails into rivnuts,and one in the front at the bottom.

But a winter job I'm hoping to do is change these over to slide latches,to make it easier and faster to remove.


CosKev3 - 11/1/18 at 08:09 PM

https://www.advantage-motorsport.co.uk/car-prep/fasteners/grayston-slide-latches-bushes-pk10-lamp-pod-panel-fastener-like-dzus.html


S1502 - 11/1/18 at 08:15 PM

quote:
Originally posted by CosKev3
https://www.advantage-motorsport.co.uk/car-prep/fasteners/grayston-slide-latches-bushes-pk10-lamp-pod-panel-fastener-like-dzus.html


Have never seen those before i was tempted to make 2 brackets fibreglassed into the top of the nose cone and rivnut into the chassis


craigdiver - 11/1/18 at 08:15 PM

this thread is a bit spooky. I was giving some thought on how to secure my nose cone too and came on here to have a search! My issue is that the nose cone comes within a couple of inches of the engine so cannot get my hand into the nose cone on the offside and very tight on the nearside.


craigdiver - 11/1/18 at 08:19 PM

quote:
Originally posted by S1502
quote:
Originally posted by CosKev3
https://www.advantage-motorsport.co.uk/car-prep/fasteners/grayston-slide-latches-bushes-pk10-lamp-pod-panel-fastener-like-dzus.html


Have never seen those before i was tempted to make 2 brackets fibreglassed into the top of the nose cone and rivnut into the chassis


The guy who made my GRP scuttle says to stick bracket to GRP with good quality no nails then glass over when fully cured. Think this is the way ill be doing it. Do like the look of those clips though.


40inches - 11/1/18 at 11:50 PM

Two hinges on the bottom and two Dzus fasteners on the side. Flips forward easily
Description
Description
Description
Description
Description
Description
Description
Description
Vents
Vents


[Edited on 12-1-18 by 40inches]


craigdiver - 12/1/18 at 07:42 AM

quote:
Originally posted by 40inches
Two hinges on the bottom and two Dzus fasteners on the side. Flips forward easily



I do like that, thanks - do you have another photo showing the whole hinge (did you fabricate the hinge yourself?)


40inches - 12/1/18 at 09:02 AM

quote:
Originally posted by craigdiver
quote:
Originally posted by 40inches
Two hinges on the bottom and two Dzus fasteners on the side. Flips forward easily



I do like that, thanks - do you have another photo showing the whole hinge (did you fabricate the hinge yourself?)


I made them out of ally angle, but you could use stainless marine hinges.
like these:Link
Or probably even better Link


nick205 - 12/1/18 at 09:18 AM

On my MK Indy I mounted the nose cone with 2x M5 cap heads into rivnuts in the top chassis rails at the rear. Plus 2x threaded studs into rivnuts in the front lower chassis rail. 4x fixings in total. Never had any issues with it. The bonnet itself overlapped and helped secure the top rear edge of the nose cone.


Building again I would look to hinge the nose cone at the lower front edge and leave the bonnet overlap to hold the top rear edge.

FYI - this was all with MK supplied bodywork.

[Edited on 12/1/18 by nick205]


craigdiver - 12/1/18 at 09:26 AM

quote:
Originally posted by 40inches
quote:
Originally posted by craigdiver
quote:
Originally posted by 40inches
Two hinges on the bottom and two Dzus fasteners on the side. Flips forward easily



I do like that, thanks - do you have another photo showing the whole hinge (did you fabricate the hinge yourself?)


I made them out of ally angle, but you could use stainless marine hinges.
like these:Link
Or probably even better Link


Perfect, thanks


40inches - 12/1/18 at 09:28 AM

quote:
Originally posted by nick205

Building again I would look to hinge the nose cone at the lower front edge .

FYI - this was all with MK supplied bodywork.

[Edited on 12/1/18 by nick205]


A bit like mine then


peter030371 - 12/1/18 at 09:44 AM

First build had 4 Dzus fasteners but they hardly ever got used (never really needed to take the nose cone off once it was sorted). On a couple of occasions one of the Dzus fasteners would pop open on track

On my latest build I have four bolts with simple brackets (made with aluminium angle) with nutserts through the side. If I do need to take it off then it takes 1 minute rather than 20 seconds but they don't pop open! Don't have any pictures of the brackets but the finished fit is like this

MOT day
MOT day


I also plan to add a front splitter at some point so wanted a 'solid' fit this time and with just the Dzus I had a little movement. Don't get me wrong I like Dzus and this time have four of them holding the bonnet on but because of the final fit these don't budge an inch unlike the old nosecone


craigdiver - 12/1/18 at 11:05 AM

quote:
Originally posted by peter030371
First build had 4 Dzus fasteners but they hardly ever got used (never really needed to take the nose cone off once it was sorted). On a couple of occasions one of the Dzus fasteners would pop open on track

On my latest build I have four bolts with simple brackets (made with aluminium angle) with nutserts through the side. If I do need to take it off then it takes 1 minute rather than 20 seconds but they don't pop open! Don't have any pictures of the brackets but the finished fit is like this

MOT day
MOT day


I also plan to add a front splitter at some point so wanted a 'solid' fit this time and with just the Dzus I had a little movement. Don't get me wrong I like Dzus and this time have four of them holding the bonnet on but because of the final fit these don't budge an inch unlike the old nosecone


Yes, seeing your nose cone disappear in your rear view mirror wouldn’t be good ;-). Great looking car

[Edited on 12/1/18 by craigdiver]