larrythelathe
|
| posted on 24/7/07 at 06:50 PM |
|
|
fault help
went out for a drive tonight after changing my blown zx9r coils. Alls fine until i give it medium poke in a low gear theress a jolt then the revs rise
and fall back to normal and it goes like normal. Anyideas what is making the revs rise and the jolt?
Roads are still damp maybe small amount of wheel spin?
|
|
|
|
|
Peteff
|
| posted on 24/7/07 at 06:55 PM |
|
|
Clutch slipping?
Sounds like it.
yours, Pete
I went into the RSPCA office the other day. It was so small you could hardly swing a cat in there.
|
|
|
larrythelathe
|
| posted on 24/7/07 at 07:13 PM |
|
|
errm
wouldn't it get worse as the revs go up?
|
|
|
ChrisGamlin
|
| posted on 24/7/07 at 07:27 PM |
|
|
a clutch is most likely to slip at peak torque, sometimes if its only marginally slipping it will bite again as you go higher up the rev range.
Do the revs rise suddenly as if in neutral thn bang back in as they match the road speed again, or is it all quite progressive. I assume by your
comment on wheelspin its more the latter? If so, it can only really be three things, either clutch slip, wheelspin or you are actually accelerating
then decelerating!
|
|
|
russbost
|
| posted on 24/7/07 at 07:44 PM |
|
|
Sounds like wheelspin to me, do you get associated tyre noise with it?
I no longer run Furore Products or Furore Cars Ltd, but would still highly recommend them for Acewell dashes, projector headlights, dominator
headlights, indicators, mirrors etc, best prices in the UK! Take a look at http://www.furoreproducts.co.uk/ or find more parts on Ebay, user names
furoreltd & furoreproducts, discounts available for LCB users.
Don't forget Stainless Steel Braided brake hoses, made to your exact requirements in any of around 16 colours.
http://shop.ebay.co.uk/furoreproducts/m.html?_dmd=1&_ipg=50&_sop=12&_rdc=1
|
NOTE:This user is registered as a LocostBuilders trader and may offer commercial services to other users
|
larrythelathe
|
| posted on 24/7/07 at 08:10 PM |
|
|
no no tire noise
it early in the rev ranf and over and done with fast around 6000 rpm then matches the road speed
|
|
|
larrythelathe
|
| posted on 24/7/07 at 08:14 PM |
|
|
repacment clutch
can any piont my towards a good replacemnet clcutch its a c1 engine
|
|
|
Wadders
|
| posted on 24/7/07 at 08:52 PM |
|
|
Kawasaki, aftermarket ones are generally crap.
Are you sure its slipping? Try setting off with the handbrake pulled on tight.
Al.
Originally posted by larrythelathe
can any piont my towards a good replacemnet clcutch its a c1 engine
[Edited on 24/7/07 by Wadders]
|
|
|
larrythelathe
|
| posted on 24/7/07 at 08:54 PM |
|
|
bugger
is there anything i can do to stop the old clutch slipping?
|
|
|
larrythelathe
|
| posted on 24/7/07 at 08:57 PM |
|
|
anygood?
http://cgi.ebay.co.uk/Kawasaki-ZX9R-98-04-EBC-Heavy-Duty-Clutch-Kit_W0QQitemZ290127809648QQihZ019QQcategoryZ25623QQrdZ1QQssPageNameZWD1VQQcmdZViewItem
|
|
|
