Cheers
Alex
Does anybody have any details of using the Jag diff in a locost.
I was asked this question late last night at work and I said i didn't know but I would find out as my workmate has a couple of them (Jag diffs in
his garage and my part is if so when would i like to collect them if I wanted them
HELP QUICK BEFORE THEY ARE BINNED
Not saying it cant be done, but theyr'e big and very heavy, also the ratios might be rather tall depending on what engine your planning to use.
The spares are pricey if you need to refurb them too. far easier to stick with sierra or maybe freelander.
Al.
]Originally posted by Blakey_boy
Does anybody have any details of using the Jag diff in a locost.
I was asked this question late last night at work and I said i didn't know but I would find out as my workmate has a couple of them (Jag diffs in
his garage and my part is if so when would i like to collect them if I wanted them
HELP QUICK BEFORE THEY ARE BINNED
No idea what the fittings are like, or width or weight but, the rear end is not dissimilar to a sierra irs.
Similar price to £100-£300, some nice ratios for BEC's too 2.88, 3.07, 3.31
I think speedyxjs (?) is building a seven using jag bits, although I've had a few out, and while they will take mountains worth of power they are
physically quite big and pretty heavy too
Cheers
Alex
TextText
Cheers for the replies so far. Have spoken to my mate and apparently though not 100% one of them is off a Soveriegn and is (supposedly) a powerlock
diff.
I have been perusing the web and havn't come up with much yet but I will keep trawling
Good site for all jag related info
http://www.jag-lovers.org/
Cheers
Alex
They are pretty heavy!! You can get an aluminium maincase for the 4HU diff, but its £1300!!!
Yikes.
If the Powerlok is going begging, I would be interested in it. Pls U2U if its available.
Thanks,
Ed.
I think Simon on here with the v8 locost was talking about fitting a jag rear end..
quote:
Originally posted by ecosse
I think speedyxjs (?) is building a seven using jag bits
v12 soverign would have had a powerlock LSD, trouble with these is they tend to bang in, not soft like a viscous one.
Also very heavy, but then jags use the 1/2 shaft as the top bone, hence the UJ's not CV joints so are very strong across the casing.
You also get inboard discs so less unsprung weight, this may overcome the weight concerns.
Regards Mark
Unless he wants to but 500 bhp through the axle it isn't a good idea.
Has he any idea how heavy this rear set up is ?
I have done a lot of major work on a lot of Jag IRS rear ends from the small version fitted to E Type up to the DS420 limo, mainly the work was
renewing the mounts and the needle roller pivot bearings. Virtually anything that had to be done to these suspensions involved dropping the rear diff
complete with its subframe --- boy is it heavy ie several hundred pounds.
The whole construction is heavy, subframe, drive shafts, uprights, lower wishbones, diff.
ed_crouch
Sorry but can't help you there
britishtrident
Yes I know it is as you put very heavy but without the frame and just the IRS, shafts and hubs. I have been toldthat it is approx 40 lbs heavier than
the sierra 71/2 unit from the cossies. (and probably a bit cheaper than a recon sierra unit)
And for the record I am using a cossie lump with T41 actuator and Turbo plus ecu which with head and cams comes out at around 330 - 350 BHP at the
flywheel
For infp pn;y I now have the lsd (powerlock) and the other which came off an kj6 has been taken by a next door neighbour who is building a Dax Tojjer
and his donor diff is knackered
Many Thanks for all comments I am now starting to look at ways of fitting it in.
Cheers
Bob
quote:
Originally posted by Blakey_boy
For infp pn;y I now have the lsd (powerlock) and the other which came off an kj6 has been taken by a next door neighbour who is building a Dax Tojjer and his donor diff is knackered
Many Thanks for all comments I am now starting to look at ways of fitting it in.
Cheers
Bob
Actually not a bad idea I will do that asap and post the findings
Just under 3 stone, not much heavier then can't see many making it into BEC's LOL 
Originally posted by Blakey_boy
I have been told that it is approx 40 lbs heavier than the sierra 71/2 unit from the cossies.