Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: Brake warning light on dual circuit bias setup?
cloudy

posted on 20/1/08 at 11:52 PM Reply With Quote
Brake warning light on dual circuit bias setup?

Can't find this info anywhere...
Will I need a sensor for both reservoirs? Or just front?

Also are there any suitable integral reservoirs for SVA?

Thanks All

James

[Edited on 20/1/08 by cloudy]

View User's Profile Visit User's Homepage View All Posts By User U2U Member
blakep82

posted on 21/1/08 at 12:04 AM Reply With Quote
i'd wondered about this too... I'm going to have 2 of everything, 2 master cylinders, 2 sensors, and 2 warning lights,
that way, if you do get a failure of one circuit, it will tell you which





________________________

IVA manual link http://www.businesslink.gov.uk/bdotg/action/detail?type=RESOURCES&itemId=1081997083

don't write OT on a new thread title, you're creating the topic, everything you write is very much ON topic!

View User's Profile View All Posts By User U2U Member
RazMan

posted on 21/1/08 at 05:33 AM Reply With Quote
That's a tricky one and technically I suppose you need to have a warning on both reservoirs. Better still, if you can have one reservoir for both brakes and the clutch, then all your bases are covered with one warning switch.





Cheers,
Raz

When thinking outside the box doesn't work any more, it's time to build a new box

View User's Profile E-Mail User Visit User's Homepage View All Posts By User U2U Member
MikeRJ

posted on 21/1/08 at 06:59 AM Reply With Quote
If you are using a remote reservoir with twin master cylinders then use one of the proper reservoirs that have one level switch and a divider between front and rear sections to stop a leak in one totaly draining the other.
View User's Profile View All Posts By User U2U Member
iank

posted on 21/1/08 at 07:53 AM Reply With Quote
Yes, if using separate reservoirs for front and rear brakes you need two switches - but you can (should?) wire them in series and only have one light/test switch - doesn't matter which ones leaking the light is there to tell you to stop immediately, diagnostics should be easy just by looking at which reservoir is below min.

Clutch cylinder doesn't need a warning light.





--
Never argue with an idiot. They drag you down to their level, then beat you with experience.
Anonymous

View User's Profile View All Posts By User U2U Member
02GF74

posted on 21/1/08 at 10:15 AM Reply With Quote
quote:
Originally posted by iank
Yes, if using separate reservoirs for front and rear brakes you need two switches - but you can (should?) wire them in series and only have one light/test switch - doesn't matter which ones leaking the light is there to tell you to stop immediately, diagnostics should be easy just by looking at which reservoir is below min.

Clutch cylinder doesn't need a warning light.


should be in parallel to make OR function; lamp is on when either one of the switches is closed.

I have a similar set up with the reservoir and handbrake switches.

View User's Profile View All Posts By User U2U Member
iank

posted on 21/1/08 at 10:32 AM Reply With Quote
quote:
Originally posted by 02GF74
quote:
Originally posted by iank
Yes, if using separate reservoirs for front and rear brakes you need two switches - but you can (should?) wire them in series and only have one light/test switch - doesn't matter which ones leaking the light is there to tell you to stop immediately, diagnostics should be easy just by looking at which reservoir is below min.

Clutch cylinder doesn't need a warning light.


should be in parallel to make OR function; lamp is on when either one of the switches is closed.

I have a similar set up with the reservoir and handbrake switches.


you are quite right. I had it in my head that the switches opened on fail. my bad.





--
Never argue with an idiot. They drag you down to their level, then beat you with experience.
Anonymous

View User's Profile View All Posts By User U2U Member
cloudy

posted on 21/1/08 at 05:14 PM Reply With Quote
Thanks guys, so basically I need to have remote reservoir(s) to be able to have warning sensors....
View User's Profile Visit User's Homepage View All Posts By User U2U Member
iank

posted on 21/1/08 at 05:29 PM Reply With Quote
If you use a manufacturer reservoir it will have the switch without being remote, also you can get caps with switches for the cylinders with integral reservoirs. Rally design sell a switch for willwood reservoirs (looks a bit of a hack as it looks like you have to drill the cap)
CBS sell one that looks nice though.
Bottom product on this page
http://www.carbuildersolutions.co.uk/master_cylinders.htm





--
Never argue with an idiot. They drag you down to their level, then beat you with experience.
Anonymous

View User's Profile View All Posts By User U2U Member
cloudy

posted on 22/1/08 at 08:18 AM Reply With Quote
nice find! They should do nicely

James

View User's Profile Visit User's Homepage View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.