Due too circumstances, Ill be selling a lot of pieces from my car which where replaced due too either being told they where faulty (then finding out they where wrong) or having too replace due to replacing something else and then not fitting. all parts are either new, very new or new but been sitting on my car for 2 years and not used - then theres the engine parts which are from either a 20k zetec or a 40k zetec. only thing thats iffy is the zetec head which i have been told can be fixed but i dont know how.

So far ive got back a few bits and prices are how much i payed and in red how much ill take but ill take offers at moment until ive sorted all parts out.

a) Megasquirt ECU £240 ( can anyone confirm which version it is?) its got a vacuum pipe but no wiring - im awaiting plug to be returned. £180


b) 2 litre Zetec low milage - with badly ported head £250 £100


c) Series 600 airbox look a likey £150 (never used) no backing plate at moment until MNR find it, if they do find it its cut for GXSR TB's (back plate £10) if not they make them too suit £120


d) Clutch for 2 litre Zetec £26 £20


e) Flywheel for 2 litre Zetec £12 £10


f) Ram air Pipe 4inch by 1ft half ft longish (ill have to measure) sure steve R wanted this and i said £5 to him (fits 600 airbox) and there should be another 3ft lenght at MNR (£10) £5 short £10 long


G) piper 285 Cams £445 £300


H) Turbo sport adjustable anadised ally cam pullys £100 £80


I) Inlet for Zetec engine to accept throttle boddies (did fit unspaced GXSR throttle boddies) £240 £100


Loads more new/old pullys, pipes, belts, cam covers, shiny bits etc just and and ill have it.

i need to sell as much as possible or i wont be able too keep car once it finally gets IVA pass, so barter with me but dont take the mick

send u2u or

07929167193
kris.mcgough@sky.com


[Edited on 12/9/10 by Krismc]

[Edited on 12/9/10 by Krismc]

Had a few people quering airbox.

Air box is slimline so fits under MNR bonnet(or similar tight spaces) easily, Has a built in cone filter, has a 4 inch inlet and the inlet is on RHS looking at it- great piece of kit.

ill confirm demensions but very similar to this



[Edited on 12/9/10 by Krismc]

first dibs on the engine please.

Andy

Yea, ill have too check all bits are there first. ill have a looky looky through week and make sure it is.

see you sat andy.

Sorry Kris, forgot about the tubing, I'm still up for it.

Stafford show this weekend though

No bother mate, ill keep it too one side.






.....'when i find it'

All U2us Replied too.

Updated list.

Megasquirt ECU With Vacuum pipe - im awaiting plug to be returned But £180 as is - UNDER OFFER


2 litre Zetec low milage - with badly ported head £100 - Andy got Dibs

Series 600 airbox look a likey (never used) no backing plate at moment until MNR find it, if they do find it its cut for GXSR TB's (back plate £10) if not they make them too suit £120 - cheap as chips

Clutch for 2 litre Zetec £20- might keep this for me

Flywheel for 2 litre Zetec £10

Ram air Pipe 4inch by 1ft and half ft longish (ill have to measure) £5 short - Coozer got dibs

Ram air Pipe 4inch by 2ft and half ft longish (ill have to measure))£10 long

piper 285 Cams £300 - might keep these for me.

Turbo sport adjustable anadised ally cam pullys £80

Steel Inlet for Zetec engine to accept throttle boddies (did fit unspaced GXSR throttle boddies)£100

Ceized 3.62 Limited slip diff im told its worth £350 unceized ha ha and with cost £30-£50 to fix so £200