Board logo

Throttle Bodies, Engine Management (ignition), DCOE Carbs + more (garage clearance)
garybee - 18/7/11 at 08:15 PM

Yamaha R1 Throttle Bodies

Set of Yamaha R1 throttle bodies complete with injectors, throttle position sensor etc. There is a small mark on the inlet side of one of the bodies that has been blended out which will not affect them in use. These are separate bodies that can be easily respaced to match your engine. Pictures are in my gallery.

£110 plus postage at cost


Weber Alpha ignition ECU for silvertop Zetec (1.8 or 2L)

Weber Alpha Ignition ECU for a silvertop zetec. This is complete with loom and has a map already installed to get you running. This is the best way to get a mappable ignition system and would be ideal for someone running DCOEs (I also have a spare set of these lying around) or bike carb's.

Description copied from Burton Power:-

Product Description.A state of the art 2D electronic ignition system featuring an ignition map of 16 RPM sites that can be upgraded to full 3D ignition management by the addition of a throttle position sensor (16 RPM x 16 engine load sites). The system features an engine speed limiter, and there is also a tachometer output drive and a gearshift lamp drive. Engine specific systems are supplied calibrated for a standard specification engine. Each kit includes: ECU, wiring harness, inlet air temperature sensor and cable ties. . ECU, WIRING, AIR TEMP SENSOR & FITTING PARTS

http://www.burtonpower.com/parts-by-fitment-type/parts-by-engine-ford/ford-zetec-e/webk97017.html

The loom was fitted to the car but not the ECU, changed my mind.

Burton have this for sale for £458, I'm looking for £250 ono.


Weber 40 DCOE carb'

Single Weber 40 DCOE. This has been standing for a while and could do with a service and will need jetting to your engine of course

£60


Fuel Swirl Pot

Aluminium Fuel Swirl Pot (unused), 150mm x 130 x 130. Complete with AN to UNF fittings for high pressure hoses.

£30


Header Tank

Aluminium header tank 150mm tall x 80 deep x 160 wide. This has a standard cap fitting but no cap. Fitted but never used, would look new with a polish.

£30


Oil Catch Tank

Aluminium oil catch tank 190mm tall x 85 deep x 130 wide with sight tube. Fitted but never used, would look new with a polish.

£30


More to be added later

Pictures for all items should be in my gallery. If I've missed anything please just give me a nudge and I will upload one for that item.

[Edited on 19/7/11 by garybee]

snapper - 19/7/11 at 05:27 AM

First ribs on the header tank and a photo of said tank please

shindha - 19/7/11 at 08:13 AM

I am intrested in the catch tank and 2nd dibd on the header tank could you send some pictures please if you have already sent me a picture of the catch tank I might have deleted it - some one sent me a picture of a header or catch tank that I asked for may be on here or some other forum. Memmory is not my greatest asset ..

shindha - 19/7/11 at 08:15 AM

DOH !! Also meant to ask is the ECU suitable for running throttle body set up - couldn't find any information on their website or on Northampton Motorsports site.

garybee - 19/7/11 at 11:25 AM

I'm afraid I don't do dibs, whoever commits to buying something first has 'dibs' on any item. I always stick rigidly to this in the interests of fairness as some people will call 'dibs' on anything they might be interested in.

The engine management setup is ignition only, so can't run throttle bodies. It's intended for use by someone running carb's.

Pictures for all items should be in my gallery. Should have said this in the original post (now edited)...sorry.

snapper - 20/7/11 at 06:09 AM

Need a photo of header tank before I commit
Outlets size and position are important as is fixing method and position.
You don't do dibs.
I don't buy blind.

garybee - 20/7/11 at 10:48 AM

quote:
Originally posted by snapper
Need a photo of header tank before I commit
Outlets size and position are important as is fixing method and position.
You don't do dibs.
I don't buy blind.


There are pictures of the items for sale in my gallery, nobody is asking you to buy blind. I will however be selling all items to whoever is the first to commit to paying for them. What I was trying to help everyone to understand is that nobody has 'dibs'.

If the descriptions in the OP and the pictures in my gallery aren't sufficient, please just ask and I will add more.

garybee - 21/7/11 at 12:02 PM

Swirl pot and header tank provisionally sold. Everything else still available.

garybee - 15/8/11 at 08:13 PM

bump...

ECU and carb' no longer available, all other items still for sale. Swirl pot and header tank still for sale too.

[Edited on 15/8/11 by garybee]

ChrisLeary - 16/8/11 at 06:57 AM

i'll have the header tank.

Cheers, chris.

obr_technology - 16/8/11 at 07:44 PM

Hi,

Do you still have the swirl pot? If so could you send over a picture?

Cheers

Olly

garybee - 17/8/11 at 07:32 AM

quote:
Originally posted by obr_technology
Hi,

Do you still have the swirl pot? If so could you send over a picture?

Cheers

Olly


Hi Olly

Yes, still have the swirl pot. There is a picture of it in my photo archive, please let me know if you need another picture and I will add.

Cheers

Gaz

garybee - 25/8/11 at 12:01 PM

Engine management and Carb's sold, all other items still available.

[Edited on 25/8/11 by garybee]