Krismc
|
| posted on 30/9/12 at 04:37 PM |
|
|
Pulley and/or Pillow block!
Im after a pulley with 20mm hole center that i can mount on my axle to connect to the drive unit on this build can any one help??
Also a pillow block or bearing mount for the axle if anyone has got one?
http://www.locostbuilders.co.uk/forum/7/viewthread.php?tid=174891
[Edited on 30/9/12 by Krismc]
Built, Ivaed, Drove and now Sold - 2011 MNR VORTX RT+ 2000cc Zetec on R1 Throttle boddies.
|
|
|
|
|
Peteff
|
| posted on 30/9/12 at 04:48 PM |
|
|
You could use a small wheel with the tyre removed.
yours, Pete
I went into the RSPCA office the other day. It was so small you could hardly swing a cat in there.
|
|
|
Krismc
|
| posted on 30/9/12 at 04:53 PM |
|
|
Actually thats what ive done for the drive end, ill take some pics.
Ill take a look on ebay then.
[Edited on 30/9/12 by Krismc]
Built, Ivaed, Drove and now Sold - 2011 MNR VORTX RT+ 2000cc Zetec on R1 Throttle boddies.
|
|
|
Krismc
|
| posted on 30/9/12 at 05:24 PM |
|
|
Cant find nothing on ebay, ill go take some pics of what i need.
Built, Ivaed, Drove and now Sold - 2011 MNR VORTX RT+ 2000cc Zetec on R1 Throttle boddies.
|
|
|
r1_pete
|
| posted on 30/9/12 at 05:39 PM |
|
|
I've a Picador 2 3 4 5 inch stepped pulley, the hole will need machining and the pulley is straight from cating so will need a light machine all
over to remove the fash.
You can have it for the postage cost, if its any good to you?
|
|
|
Krismc
|
| posted on 30/9/12 at 05:42 PM |
|
|
Cant machine anything or weld for that matter, i need a part where all it needs is cutting, filing, grinding or bolting in place.
here is the car as is.... I either need one pulley or replace both.
[Edited on 30/9/12 by Krismc]
Built, Ivaed, Drove and now Sold - 2011 MNR VORTX RT+ 2000cc Zetec on R1 Throttle boddies.
|
|
|
Brian R
|
| posted on 30/9/12 at 08:34 PM |
|
|
I've used these several times for bearings etc. Very good and usually next day delivery.
http://simplybearings.co.uk/shop/
|
|
|
Krismc
|
| posted on 1/10/12 at 05:19 PM |
|
|
Im still wondering where to get a 20mm bore pulley from. anyone got a one lying around that i can bash the bearing out off.
[Edited on 1/10/12 by Krismc]
Built, Ivaed, Drove and now Sold - 2011 MNR VORTX RT+ 2000cc Zetec on R1 Throttle boddies.
|
|
|
Brian R
|
| posted on 1/10/12 at 09:43 PM |
|
|
How about this?
RDGTOOLS ALUMINIUM 4 STEP V PULLEY WITH A 20MM BORE | eBay
Fit one on the motor and another on the axle the opposite way round to get optimum gear ratios?
|
|
|
Krismc
|
| posted on 2/10/12 at 05:36 AM |
|
|
Perfect apart from the price, it's a 1/5 locost so I expect 1/5 locost prices. 5er max.
Built, Ivaed, Drove and now Sold - 2011 MNR VORTX RT+ 2000cc Zetec on R1 Throttle boddies.
|
|
|
