big_wasa
|
| posted on 4/1/06 at 10:13 PM |
|
|
Made some progress....On a roll...
Well im determined to have the engine in and running and on its wheels by Easter.
So must crack on 
Made the rack mounts, over did it a bit (all 3mm plate ) It wont be going far!
Trial fitted the front wishbones, rack and uprights.
Cycled it all to check for bump-steer. Still a bit of tidying to do.
 
|
|
|
|
|
big_wasa
|
| posted on 4/1/06 at 10:14 PM |
|
|
pic 2
|
|
|
Genesis
|
| posted on 4/1/06 at 10:16 PM |
|
|
Looks good - reach around and pat yourself on the back... top job!!!
Going fishin'
|
|
|
Danozeman
|
| posted on 4/1/06 at 10:20 PM |
|
|
Top job mate. The way your going it will be finished by easter,
Dan
Built the purple peril!! Let the modifications begin!!
http://www.eastangliankitcars.co.uk
|
|
|
Avoneer
|
| posted on 4/1/06 at 10:39 PM |
|
|
Hi Big-W,
Hope you're gonna brace those top bone brackets, either with a horizontal bar between the two or with some plate.
P.S. Those ali clamps look really good 
Pat...
No trees were killed in the sending of this message.
However a large number of electrons were terribly inconvenienced.
|
|
|
big_wasa
|
| posted on 4/1/06 at 10:49 PM |
|
|
Yep next job. It will depend on how I mount the shocks.
|
|
|
big_wasa
|
| posted on 4/1/06 at 10:53 PM |
|
|
Yep mounts are good, dont spose you have the rubber bits learking in your garage Pat?
regards warren
|
|
|
RichardK
|
| posted on 4/1/06 at 11:01 PM |
|
|
Looking great, hope mine turns out as well.
|
|
|
Peteff
|
| posted on 4/1/06 at 11:26 PM |
|
|
dont spose you have the rubber bits learking in your garage
Get an old inner tube from your local tyre outlet and cut it into strips the right width then wind it round the rack till you have the right thickness
and stick the clamps on over it.
yours, Pete
I went into the RSPCA office the other day. It was so small you could hardly swing a cat in there.
|
|
|
Avoneer
|
| posted on 4/1/06 at 11:47 PM |
|
|
Hi Big-W.
No, sorry mate, I never got any with them - didn't think you needed them either.
Racing bike inner tube is a good idea though.
Sorry,
Pat...
No trees were killed in the sending of this message.
However a large number of electrons were terribly inconvenienced.
|
|
|
big_wasa
|
| posted on 5/1/06 at 08:33 AM |
|
|
No probs Pat ........Still great mounts.
|
|
|
viatron
|
| posted on 5/1/06 at 01:17 PM |
|
|
Arent those Rally Design clamps? Same as mine. To get the fit right i tried Rubber but they only need a very thin piece. ended up using Pop bottle
plastic cut into a strip and wound round once. It wont compress like rubber and is weatherproof and doesnt degrade.
Mac
|
|
|
Alan B
|
| posted on 5/1/06 at 01:19 PM |
|
|
I wouldn't worry about the 3mm for the rack mount....looks and seems about right to me..
|
|
|
big_wasa
|
| posted on 7/1/06 at 11:00 PM |
|
|
quote:
Originally posted by Avoneer
Hi Big-W,
Hope you're gonna brace those top bone brackets, either with a horizontal bar between the two or with some plate.
Pat...
So Pat do you think that will do it ?
regards warren
|
|
|
%20(WinCE).JPG)
