Board logo

where is the edis4??
boggle - 23/3/10 at 07:42 PM

can anyone tell me where the edis4 module is located on a ford???

cheers

barry

big_wasa - 23/3/10 at 07:48 PM

Fiesta/ escort = Inner N/s wing behind head lamp or top middle of engine bulkhead.

Auto Mondeo = top middle of engine bulkhead.

Sierra = O/s inner wing.

jonesier1 - 23/3/10 at 07:49 PM

normally on the n/s inner wing on an escort and on the bulkhead panel on a fiesta.

mcerd1 - 23/3/10 at 07:58 PM

the auto mondeo is your best bet

most escorts just have a dizzy from about 95 onwards as far as I could tell

boggle - 23/3/10 at 08:00 PM

we have a few mk5's and 6's aswell as some fiestas and mondeos in the scrappy next door...

what type of fiesta would i be looking for??

cheers

barry

big_wasa - 23/3/10 at 08:01 PM

1.1 and 1.3 endura engine

G reg throught N reg ish

mcerd1 - 23/3/10 at 08:03 PM

probably a mk3 fiesta or a Mk 4 escort
try the 1.3 and 1.6's

boggle - 23/3/10 at 08:04 PM

cheers guys....would the ford ka have one???

mcerd1 - 23/3/10 at 08:06 PM

no its too modern (its all done by the ECU) but it will have a VR sensor and coil pack thought

[Edited on 23/3/10 by mcerd1]

big_wasa - 23/3/10 at 08:07 PM

never seen one in a ka

boggle - 23/3/10 at 08:13 PM

vr sensor is the crank position sensor???

big_wasa - 23/3/10 at 08:36 PM

Its the type of sensor used for the cps some makes use Hall affect like some vw's some use Vr.

just stick the term into wiki and it will give you all the science........

boggle - 23/3/10 at 08:40 PM

ok...worst case scenario does anyone sell the parts.....??

just bought a megajolt unit with loom and software...just need the coil, vf and edis4...i have a tps on the bike carbs i have bought....

mcerd1 - 23/3/10 at 08:41 PM

quote:
Originally posted by boggle
vr sensor is the crank position sensor???


yes, its easier to find on some than others - its aimed at the flywheel and goes throught the block - some have it on the front and others its on the back

if you can't get at one on the same car as the rest of it then try one with a zetec (same sensor)
oh and try to hang on to a good length of the sheilded cable that its connected with

quote:
Originally posted by boggle
ok...worst case scenario does anyone sell the parts.....??

yes (ebay, trigger-wheels.com) but its normaly no where near as cheap


as an example: I got most of mine from a 1.3 K reg escort (apart from the VR sensor as it didn't want to let go)
I managed to get the whole loom out without cutting any of the bits I needed too (took ages to strip the wires back enough thought....)



[Edited on 23/3/10 by mcerd1]

big_wasa - 23/3/10 at 08:45 PM

Just keep looking I havnt got a spare one at the min but I will have another look next time I go for a look around.

boggle - 23/3/10 at 08:58 PM

thanks for all the replys and help

paulf - 23/3/10 at 09:27 PM

I have a few spare Edis parts and think I could sort out what you need if you are really stuck.
Paul.

quote:
Originally posted by boggle
ok...worst case scenario does anyone sell the parts.....??

just bought a megajolt unit with loom and software...just need the coil, vf and edis4...i have a tps on the bike carbs i have bought....

boggle - 23/3/10 at 09:30 PM

thanks paulf....

i will look in the scrappy tommorow then let you know...

cheers

barry