Board logo

Zetec Loom plug Ident
tims31 - 10/3/12 at 04:51 PM

After some help please guys, could you all with your wealth of knowledge please ident all the plugs on this zetec loom for me. I'm sure big wassa will be able to but if any of you can help that would be great, thanks

Zetec-ECU-Loom
Zetec-ECU-Loom Description
Description Description
Description Description
Description Description
Description

The Injector part has the ident 98BG-9H589
The main part is 97BG-12A522-CDB

[Edited on 10/3/12 by tims31]

[Edited on 10/3/12 by tims31]

AndyW - 10/3/12 at 05:37 PM

13) Crank position sensor
12) Water temp (One of two)
11) Cam position sensor
8) other water temp
5) O2 lambda sensor
4) 42 pin plug to car loom
3,2 & 1 again cant quite see but air flow meter, throttle position switch & bu&&er cant remember.

Will have a look at my spare loom later if I get chance

big_wasa - 10/3/12 at 07:57 PM

1) Coil
2) Supressor
3) Maff
4) C2513
5) Lambda
6) ------------------- Egr from memory
7) -------------------- Egr from memory
8) Coolant temp sensor for ecu
9) Idle controle valve
10) Throttle position sensor
11) Cam position sensor
12) coolant temp sensor for dash
13) Crank position sensor
14) Alternator
15) Low oil pressure

tims31 - 10/3/12 at 11:29 PM

See, I was right. I knew you would know what they all were big_wasa

The big 42 pin plug (C2513) is that needed? Do I need elements of the car loom to get this to work? What about 6+7?

I have an OWLS ECU as you suggested with the key and sensor with it. Is this loom going to work ok with this ECU? I really need to pop round and see you again so you can take a look at this for your expert view.

Hows your Pre-IVA going?

big_wasa - 11/3/12 at 12:47 PM

pop around mate I am on the drive playing with mine.

AndyW - 11/3/12 at 12:51 PM

IVA booked yet Warren??

big_wasa - 11/3/12 at 12:54 PM

eeeeeeeeeerm no

i_froloshki - 2/4/12 at 01:59 PM

quote:
Originally posted by big_wasa
1) Coil
2) Supressor
3) Maff
4) C2513
5) Lambda
6) ------------------- Egr from memory
7) -------------------- Egr from memory
8) Coolant temp sensor for ecu
9) Idle controle valve
10) Throttle position sensor
11) Cam position sensor
12) coolant temp sensor for dash
13) Crank position sensor
14) Alternator
15) Low oil pressure


Hi,
one question from me as well - what should i do with the C2513 item? I am using the zetec ECU with all its additional items - MAF, throttle, injectors and custom plenum. I am going to use dolphin gadgets and eddie 99 loom. The other thing is that i have to think of something about the air temp. sensor - where to put it. Any information will be helpful.

Thanks

Yavor

big_wasa - 2/4/12 at 04:19 PM

You can cut the plug of car side and wire it into your loom or the way I prefer is to cut it up and custom re-build the loom to fit the car.

Air temp sensor will depend on what ecu you use. Its built into the Maf on the black top. On my silver top I stick them in the plenum.

[Edited on 2/4/12 by big_wasa]