mad4x4
|
| posted on 18/6/06 at 09:16 PM |
|
|
HELP
Need a quick solution to this problem
The CPS (Crank Shaft Position Sensor) mount on my zetec I have installed is wrong, so no Spark
I have the automation one and need a manual one.
This can only be changed by engine removal and removal of Fly Wheel.
Can anyone come up with a solution to changing this on a zetec without removal of engine / flywheel. Could it be ground or drilled?
Scot's do it better in Kilts.
MK INDY's Don't Self Centre Regardless of MK Setting !
|
|
|
|
|
big_wasa
|
| posted on 18/6/06 at 10:01 PM |
|
|
No mate bite the bullet. The sensor runs very close in a harsh environment.
|
|
|
MkIndy7
|
| posted on 18/6/06 at 10:57 PM |
|
|
Not exactly an easy solution but maybe a "get u out"
If its the EDIS ignition set-up, could you not mount a pick-up wheel on the Crank Pully as per 1.8CVH setup.
Just a thought!
|
|
|
mad4x4
|
| posted on 19/6/06 at 06:12 AM |
|
|
quote:
Originally posted by big_wasa
No mate bite the bullet. The sensor runs very close in a harsh environment.
Yeah but I only have 11 days to my SVA and I still need to now
1 Get the alternator mounted & working
2 Plumb in the engine
3 Change the CPS sensor & Get it to start.
4 Tune the engine - Set the carbs
4.5 Re-weld the exhaust if it leaks
5 Tidy the wiring
6 Test run (s)
Oh and work 12hours a day and weekends for the next 2 -3 weeks at my JOB 
OH SHIT !! Looks like I need to be ill for a day or two.
Scot's do it better in Kilts.
MK INDY's Don't Self Centre Regardless of MK Setting !
|
|
|
mad4x4
|
| posted on 19/6/06 at 06:20 AM |
|
|
quote:
Originally posted by MkIndy7
Not exactly an easy solution but maybe a "get u out"
If its the EDIS ignition set-up, could you not mount a pick-up wheel on the Crank Pully as per 1.8CVH setup.
Just a thought!
Does this pully fit the Zetec or is it wider - won't this sit to far out to drive the water pump
Scot's do it better in Kilts.
MK INDY's Don't Self Centre Regardless of MK Setting !
|
|
|
Wadders
|
| posted on 19/6/06 at 08:09 AM |
|
|
I think what he means is mount a trigger wheel on your existing zetec front pulley.
Does this pully fit the Zetec or is it wider - won't this sit to far out to drive the water pump
|
|
|
MkIndy7
|
| posted on 19/6/06 at 06:52 PM |
|
|
Yup ment just the toothed wheel,
They can either be forced off a CVH pully from the Scrap yard or I'm sure someone on here has posted a Ford part No for a new one,
Then mount this to your crank pully and fabricate a mount for the pick-up sencor.
To learn more about the pick-up wheels try looking up Megajolt on here or the Net and megasquirtnSpark both use the EDIS system and its associated
sencors.
|
|
|
big_wasa
|
| posted on 19/6/06 at 07:01 PM |
|
|
yep the triger wheel up front will work but I think you will find it more work than droping the motor and doing your own.
|
|
|
