Board logo

Rolling road result !
clairetoo - 25/7/10 at 08:46 PM

As a few on here will know , I have just completed another V6 Mazda conversion in a Fury - and it got on a rolling road for a proper set-up yesterday .
And..............bearing in mind it is a £200 ebay engine - it made 205.9 BHP @ 7000 RPM

I had predicted around the 200 mark - I am well chuffed


rear left view
rear left view

[Edited on 25/7/10 by clairetoo]

RichardK - 25/7/10 at 08:49 PM

That looks very nice, you must be really chuffed.

Nice one

Rich

stevebubs - 25/7/10 at 08:50 PM

Looks a good clean install there, and excellent result on rollers

MakeEverything - 25/7/10 at 09:10 PM

Nice result, well done. What was your torque figure out of interest?

clairetoo - 25/7/10 at 09:12 PM

quote:
Originally posted by MakeEverything
Nice result, well done. What was your torque figure out of interest?

176 Lb/Ft - so a bit up on stock

iank - 25/7/10 at 09:30 PM

Looks like it was designed to be installed in that engine bay.

Carbon looks pretty good as well (and I'm not normally a fan)

What ECU are you using?

clairetoo - 25/7/10 at 09:34 PM

quote:
Originally posted by iank
Looks like it was designed to be installed in that engine bay.

Carbon looks pretty good as well (and I'm not normally a fan)

What ECU are you using?

Megasquirt - Ms1/extra and edis - it allso has an Lc1 on there , but it wont work , so no chance to check the fueling before it went to the rolling road
But the RR guy did say there wasnt a lot wrong with the mapping , it just needed `fine tuning'

iank - 25/7/10 at 09:37 PM

quote:
Originally posted by clairetoo
quote:
Originally posted by iank
Looks like it was designed to be installed in that engine bay.

Carbon looks pretty good as well (and I'm not normally a fan)

What ECU are you using?

Megasquirt - Ms1/extra and edis - it allso has an Lc1 on there , but it wont work , so no chance to check the fueling before it went to the rolling road
But the RR guy did say there wasnt a lot wrong with the mapping , it just needed `fine tuning'


Finding a RR happy to map a Megasquirt sounds like a result in itself

MakeEverything - 25/7/10 at 09:39 PM

quote:
Originally posted by clairetoo
has an Lc1 on there , but it wont work


I bought one brand new and it arrived fked. I sent it back and they gave me my money back with the return postage as well once they had checked it out. Rather annoying really, as i would have preferred to have kept it.

RazMan - 25/7/10 at 11:27 PM

Bang on the mark I'd say Claire - nice carbon too

Ninehigh - 25/7/10 at 11:35 PM

Want it!

suparuss - 26/7/10 at 02:43 AM

out of interest- where did you take it and how much does it cost to fine tune megasquirt these days?

clairetoo - 26/7/10 at 05:54 AM

It was done at Bailey Performance in Broseley - just found out that I was told wrong on the phone , the torque is actually 167 .
Graham has posted the results on sylva chat , but I cant see it as it's a `.tif' whatever that means

IanBrace - 26/7/10 at 07:07 AM

Nice one Claire, I think that was the carbon you were working on when I came over for the compressor! Looks great in the car..