Printable Version | Subscribe | Add to Favourites
New Topic New Poll New Reply
Author: Subject: Front brakes (Brembo)
b14wrc

posted on 21/2/16 at 11:35 AM Reply With Quote
Front brakes (Brembo)

Hi,

I did some development work ages ago with a 15" wheel, since then I've gone to 16" wheels so have revised the brakes, these discs fit much better with the caliper and mounting will be very easy.

Budget big brake kit that works with cortina hubs/uprights:







Rob





20vt powered rear engined locost

View User's Profile E-Mail User View All Posts By User U2U Member
JAG

posted on 21/2/16 at 04:31 PM Reply With Quote
Very good.

So what size discs?

Where are the calipers from?

What size pistons in the calipers?





Justin


Who is this super hero? Sarge? ...No.
Rosemary, the telephone operator? ...No.
Penry, the mild-mannered janitor? ...Could be!

View User's Profile View All Posts By User U2U Member
Ugg10

posted on 21/2/16 at 05:05 PM Reply With Quote
Caprisport do a very similar setup for the capri (similar upright) using the Fiat Coupe Turbo brembo's, think Alfa and Porsche use the same calipers as well.

http://stores.ebay.co.uk/Caprisport-Direct





---------------------------------------------------------------
1968 Ford Anglia 105e, 1.7 Zetec SE, Mk2 Escort Workd Cup front end, 5 link rear
Build Blog - http://Anglia1968.weebly.com

View User's Profile View All Posts By User U2U Member
b14wrc

posted on 21/2/16 at 05:19 PM Reply With Quote
Hey,

I contacted Capri sport years ago and wouldn't tell me the origin of the discs they used.

Basically my set up uses a 305mm Peugeot 406 V6 disc, initially I was using the smaller 282.5mm one when intending to use 15s. I am using the Fiat coupe standard Brembos. Not rebuilt them yet but I think the pistons are about 40mm, they use two different sizes I think. There in good condition and came with my donor car.

The discs are from Mtec and I asked them to machine the centre bore to 68mm so all I now have to do is redrill the disc, easy job, disc is a nice snug fit on the hub.

Looked at the web link, £460 isn't bad for their kit and the bigger 315mm disc would have been nice, but my kit cost me about £105 in total, I can make some steel brackets out of some plate pretty easy. Plus I got the black coated discs and they are grooved.





20vt powered rear engined locost

View User's Profile E-Mail User View All Posts By User U2U Member
b14wrc

posted on 17/11/18 at 08:13 PM Reply With Quote
Just a little update, going to go two piece, 330mm disc and escort cosworth bells.



Rob





20vt powered rear engined locost

View User's Profile E-Mail User View All Posts By User U2U Member
steve m

posted on 17/11/18 at 11:15 PM Reply With Quote
If, the brakes and disks that are pictured above, are for the car in the "work shop build" thread, then you are way way over braked,

You would need to put your foot on the brake peddle, as though trying not to break an egg, and your front brakes will still lock up

Just from experience, large disks, and multi pot calipers, do not work well on a car weighing not a lot

steve





Thats was probably spelt wrong, or had some grammer, that the "grammer police have to have a moan at




View User's Profile View All Posts By User U2U Member
b14wrc

posted on 17/11/18 at 11:59 PM Reply With Quote
Yes they may well be, but they look cool!

350bhp I think I'll need some decent brakes, running a 283mm disc and 2 pot on the rear.





20vt powered rear engined locost

View User's Profile E-Mail User View All Posts By User U2U Member
JAG

posted on 19/11/18 at 11:46 AM Reply With Quote
Interesting conversation

So; 350bhp means you'll need heavy discs as the horsepower will create a lot of Kinetic Energy which will make the discs very hot when you try to stop or slow the car. To cool the now hot discs you need lots of surface area to improve the cooling rate so vented make sense...

But; the very lightweight (I'm assuming less than 700 kg without anyone in it) nature of a Seven will make the pedal very light with such large diameter discs and multi-piston calipers.

I'd try and find some Calipers with smaller pistons or thicker but smaller diameter discs.

But it's your car and you could manage without doing any of that





Justin


Who is this super hero? Sarge? ...No.
Rosemary, the telephone operator? ...No.
Penry, the mild-mannered janitor? ...Could be!

View User's Profile View All Posts By User U2U Member
b14wrc

posted on 19/11/18 at 10:20 PM Reply With Quote
Thanks Justin,

I haven't got the disc yet, hence the mock up, but I think the two piece disc will be the equivalent weight of the single cast unit.

The plan is to machine the cortina hubs to allow the bells to fit over the hub mounting face and I'll turn off the original disc mountings. These Brembos have two different piston sizes, and as I remember in the coupe weren't all that good, full rebuild and decent discs I think it will work well, going to run an OBP pedal box and will adjust the bias, will experiment from there.

Rob





20vt powered rear engined locost

View User's Profile E-Mail User View All Posts By User U2U Member
b14wrc

posted on 20/8/20 at 10:08 AM Reply With Quote
I 3D printed an accurate 330mm rotor to fit my Escort Cosworth bells, will mock up the bracket adaptors I need too before I complete the front end running gear.







Useful tool for mocking up parts to check clearances and that, hubs still need som machining but the work shop is getting there, once wired and painted I should be able to get back to the locost in the new year.

Rob





20vt powered rear engined locost

View User's Profile E-Mail User View All Posts By User U2U Member

New Topic New Poll New Reply


go to top






Website design and SEO by Studio Montage

All content © 2001-16 LocostBuilders. Reproduction prohibited
Opinions expressed in public posts are those of the author and do not necessarily represent
the views of other users or any member of the LocostBuilders team.
Running XMB 1.8 Partagium [© 2002 XMB Group] on Apache under CentOS Linux
Founded, built and operated by ChrisW.