wacomuk
|
| posted on 26/7/09 at 07:09 PM |
|
|
ALLOY WHEELS EBAY
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=330347619255
http://www.insightbookingsolutions.co.uk
|
|
|
|
|
handyandy
|
| posted on 26/7/09 at 07:14 PM |
|
|
they look smart,
sorry, really dumb question....... would they fit the sierra hub? i see the measurements given but to be honest i don,t know enough about wheel
fitment.
thanks
andy
|
|
|
omega0684
|
| posted on 26/7/09 at 07:18 PM |
|
|
how much would it cost to have that bent alloy put right? looks FUBAR'D to me 
|
|
|
handyandy
|
| posted on 26/7/09 at 07:25 PM |
|
|
quote:
Originally posted by omega0684
how much would it cost to have that bent alloy put right? looks FUBAR'D to me
sorry to ask Omega0684 but would they fit sierra hubs?
please excuse my lack of knowledge
thanks
andy
|
|
|
Peteff
|
| posted on 26/7/09 at 07:53 PM |
|
|
They are dual PCD so they should fit anything with one of the sets of holes. The alloy is bent not fractured so it should be repairable. I've
seen bike rear rims with similar damage straightened and no problems.
yours, Pete
I went into the RSPCA office the other day. It was so small you could hardly swing a cat in there.
|
|
|
Guinness
|
| posted on 26/7/09 at 07:54 PM |
|
|
quote:
Originally posted by handyandy
quote:
Originally posted by omega0684
how much would it cost to have that bent alloy put right? looks FUBAR'D to me
sorry to ask Omega0684 but would they fit sierra hubs?
please excuse my lack of knowledge
thanks
andy
Andy
108 will fit a four stud Ford.
You'll need some more info on the offset before you decide if they are right for you though.
Mike
|
|
|
handyandy
|
| posted on 26/7/09 at 07:59 PM |
|
|
quote:
Originally posted by Guinness
quote:
Originally posted by handyandy
quote:
Originally posted by omega0684
how much would it cost to have that bent alloy put right? looks FUBAR'D to me
sorry to ask Omega0684 but would they fit sierra hubs?
please excuse my lack of knowledge
thanks
andy
Andy
108 will fit a four stud Ford.
You'll need some more info on the offset before you decide if they are right for you though.
Mike
ok thanks Mike,
i,ll make contact with seller or thru "wacomuk" who posted the thread.
i too have seen bike alloy wheels repaired ( i,ve dented a few in my racing past ).
what offset would they need to be ?
again sorry for lack of knowledge
cheers
andy
|
|
|
Gazeddy
|
| posted on 26/7/09 at 09:41 PM |
|
|
Personally wouldn't trust a repaired wheel especially a dezent wheel have seen them bend at very little and have seen several sets become porous
rather quickly
|
|
|
wacomuk
|
| posted on 26/7/09 at 09:48 PM |
|
|
The off set is ET40
Iv had wheels fixed before with out problems.
iv seen wheels with chunks missing fixed with no problems
The wheel has been looked at by Clip engineering and they say it can be fixed
[Edited on 26/7/09 by wacomuk]
http://www.insightbookingsolutions.co.uk
|
|
|
ashg
|
| posted on 26/7/09 at 10:25 PM |
|
|
andy why do you want 17inch wheels on the kit car they are too big for your triton wheel arches and will make the thing look like its on stilts
Anything With Tits or Wheels Will cost you MONEY!!
Haynes Roadster (Finished)
Exocet (Finished & Sold)
New Project (Started)
|
|
|
handyandy
|
| posted on 26/7/09 at 10:50 PM |
|
|
quote:
Originally posted by ashg
andy why do you want 17inch wheels on the kit car they are too big for your triton wheel arches and will make the thing look like its on stilts
ah, point taken Ash, thanks.
andy
ps
am just about to u2u you.
|
|
|
